BS EN 623-5-2009 高级工业陶瓷.单片陶瓷.一般和结构特性.第5部分:利用显微图像评估法测定相体积分数

百检网 2021-08-03
标准号:BS EN 623-5-2009
中文标准名称:**工业陶瓷.单片陶瓷.一般和结构特性.第5部分:利用显微图像评估法测定相体积分数
英文标准名称:Advanced technical ceramics - Monolithic ceramics - General and textural properties - Part 5: Determination of phase volume fraction by evaluation of micrographs
标准类型:Q32
发布日期:2009/8/31 12:00:00
实施日期:2009/8/31 12:00:00
中国标准分类号:Q32
国际标准分类号:81.060.30
引用标准:EN 1006;EN ISO/IEC 17025
适用范围:This part of EN 623 specifies a manual method of making measurements for the determination of volume fraction ofmajor phases in advanced technical ceramics using micrographs of polished and etched sections, overlaying a squaregrid of lines, and counting the number of intersections lying over each phase.NOTE 1 This method assumes that the true phase volume fractions are equivalent to area fractions on a randomly cut crosssectionaccording to stereological principles.NOTE 2 Guidelines for polishing and etching of advanced technical ceramics can be found in Annexes A and B.The method applies to ceramics with one or more distinct secondary phases, such as found in Al2O3/ZrO2, Si/SiC,orAl2O3/SiCw.If the test material contains discrete pores, these can be treated as a secondary phase for the purpose of this methodprovided that there is no evidence of grain pluck-out during polishing being confused with genuine pores.NOTE 3 If the material contains more than about 20 % porosity there is a strong risk that the microstructure will be damagedduring the polishing process, and measurement of volume fraction of pores may become misleading.Secondary phase volume fractions or porosity present at levels of less than 0,05 are subject to considerable error andpotential scatter in results. A larger number of micrographs than the minimum of three is normally needed to improvethe consistency and accuracy of the results.NOTE 4 Many ceramics contain small amounts of secondary glassy phases. In order to make a reasonable estimate ofglassy phase content, the glass material between crystalline grains should be readily observable, and thus should be at least0,5 μm in width. The method in this European Standard is not considered appropriate for narrow glassy films around grains.This method assumes that the selected regions of a prepared cross-section are statistically representative of the wholesampled section.NOTE 5 Microstructures are seldom homogeneous, and the phase contents can vary from micrograph to micrograph. It isessential to survey a sufficiently wide area of the prepared section to ensure that those areas selected for evaluation arerepresentative, and do not contain eye-catching irregularities.Some users of this European Standard can wish to apply automatic or semiautomatic image analysis to micrographs ordirectly captured microstructural images. This is currently outside the scope of this European Standard, but someguidelines are given in Annex C.

百检能给您带来哪些改变?

1、检测行业全覆盖,满足不同的检测;

2、实验室全覆盖,就近分配本地化检测;

3、工程师一对一服务,让检测更精准;

4、免费初检,初检不收取检测费用;

5、自助下单 快递免费上门取样;

6、周期短,费用低,服务周到;

7、拥有CMA、CNAS、CAL等权威资质;

8、检测报告权威有效、中国通用;

客户案例展示

  • 上海朗波王服饰有限公司
  • 浙江圣达生物药业股份有限公司
  • 天津市长庆电子科技有限公司
  • 上海纽特丝纺织品有限公司
  • 无锡露米娅纺织有限公司
  • 东方电气风电(凉山)有限公司
相关商品
相关问答