ASME PTB-1-2009 美国机械工程师协会第VIII节第2分册标准和评注

百检网 2021-08-04
标准号:ASME PTB-1-2009
中文标准名称:美国机械工程师协会第VIII节第2分册标准和评注
英文标准名称:ASME Section VIII Division 2 Criteria and Commentary
标准类型:J98
发布日期:2009/1/1 12:00:00
实施日期:1999/12/31 12:00:00
中国标准分类号:J98
国际标准分类号:23.020.30
适用范围:Part 1, paragraph 1.2 defines the scope of coverage for VIII-2. The term scope refers to both the type of pressure equipment being considered in the development of these rules, as well as the geometric scope of the vessel that is stamped as meeting VIII-2. In accordance with Part 1, paragraph 1.2.1.1, pressure vessels are defined as containers for the containment of pressure, internal or external. This pressure may be obtained from any external source, or by the application of heat from a direct or indirect source, as a result of a process, or any combination thereof. The manner in which the scope of the standard is described follows very closely to the introduction section of VIII-1. In the following paragraphs, a discussion of requirements is provided only where a significant difference exists between VIII-2 and the scope definition from VIII-1, or where a major change was made from Old VIII-2. With regard to pressure vessels installed in non-stationary applications, Part 1, paragraph 1.2.1.2.b now permits stamping of VIII-2 vessels installed on motor vehicles and railway cars. This particular application was prohibited in the Old VIII-2. Construction and stamping of VIII-2 vessels in nonstationary applications requires a prior written agreement with the local jurisdictional authority covering operation and maintenance control for a specific service. This operation and maintenance control must be retained during the useful life of the pressure vessel by the user in conformance with the Users Design Specification. Part 1, paragraph 1.2.1.2.e.3 defines pressure vessels in which steam is generated but which are not classified as Unfired Steam Boilers that require construction in accordance with the rules of Section I or VIII-1. A third category for a vessel that generates steam that may be constructed to VIII-2 was added: vessels in which steam is generated but not withdrawn for external use. One significant difference between VIII-2 and the Old VIII-2 is special service vessels such as those in lethal service. In Old VIII-2, paragraph AG-301.1(c) , the user and/or his designated agent had to define in the UDS if a vessel was intended for lethal service. If lethal service was specified, then additional technical requirements (e.g. enhanced NDE, restrictions on material, etc.) were imposed on this vessel. In VIII-2, additional requirements are not specified for lethal service or any other special service condition. The rationale behind this change is that the user and/or his designated agent are responsible to describe in the UDS (see Part 2, paragraph 2.2.2), the intended operation of the vessel, and if a vessel is intended for a service that is dangerous to life and property, then the user should specify any additional requirements to mitigate the risks. Just as it has been the rule in ASME that its standards would not define when a vessel is in lethal service, what additional requirements would be appropriate for any given vessel are best defined by the user, and not by the Committee.

百检能给您带来哪些改变?

1、检测行业全覆盖,满足不同的检测;

2、实验室全覆盖,就近分配本地化检测;

3、工程师一对一服务,让检测更精准;

4、免费初检,初检不收取检测费用;

5、自助下单 快递免费上门取样;

6、周期短,费用低,服务周到;

7、拥有CMA、CNAS、CAL等权威资质;

8、检测报告权威有效、中国通用;

客户案例展示

  • 上海朗波王服饰有限公司
  • 浙江圣达生物药业股份有限公司
  • 天津市长庆电子科技有限公司
  • 上海纽特丝纺织品有限公司
  • 无锡露米娅纺织有限公司
  • 东方电气风电(凉山)有限公司