ISO 10816-4-2009 机械振动.通过在非旋转部件上的测量评价机械振动.第4部分:带有流体膜轴承的燃气轮机组

标准号：ISO 10816-4-2009
中文标准名称：机械振动.通过在非旋转部件上的测量评价机械振动.第4部分:带有流体膜轴承的燃气轮机组
英文标准名称：Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 4: Gas turbine sets with fluid-film bearings
标准类型：J04;Z32
发布日期：1999/12/31 12:00:00
实施日期：1999/12/31 12:00:00
中国标准分类号：J04;Z32
国际标准分类号：17.160;27.040
引用标准：ISO 7919-4;ISO 10816-1-1995
适用范围：This part of ISO 10816 establishes provisions for evaluating the severity of in-situ, broad-band vibrationmeasured radial (i.e. transverse) to the shaft axis on all main bearing housings or pedestals and in the axialdirection on thrust bearings. These are in terms of:- vibration under normal steady-state operating conditions;- vibration during other (non-steady-state) conditions when transient changes are taking place, includingrun up or run down, initial loading and load changes;- changes in vibration which can occur during normal steady-state operation.This part of ISO 10816 is applicable to heavy-duty gas turbine sets used in electrical and mechanical driveapplications, with fluid-film bearings, outputs greater than 3 MW and an operating speed range under loadbetween 3 000 r/min and 30 000 r/min. This includes gas turbines coupled to other rotating machinery eitherdirectly or through a gearbox. In some cases, this part of ISO 10816 is not applicable to the evaluation of thevibration of the coupled equipment (see the list of exclusions in this clause).EXAMPLE For single-shaft combined-cycle power units in which a gas turbine is coupled to a steam turbine and/orgenerator, the evaluation of the gas turbine vibration is according to this part of ISO 10816, but that of the steam turbineand generator is according to ISO 10816-2 or ISO 10816-3.This part of ISO 10816 is not applicable to the following:a) aero-derivative gas turbines (including gas turbines with dynamic properties similar to those of aeroderivatives);NOTE ISO 3977-3 defines aero-derivatives as aircraft propulsion gas generators adapted to drive mechanical,electrical or marine propulsion equipment. Large differences exist between heavy-duty and aero-derivative gasturbines, for example in casing flexibility, bearing design, rotor to stator mass ratio and mounting structure. Differentcriteria therefore apply for these two turbine types.b) gas turbines with outputs less than or equal to 3 MW (see ISO 10816-3);c) gas turbine driven pumps (see ISO 10816-7);d) coupled steam turbines and/or generators with outputs less than or equal to 50 MW (see ISO 10816-3);e) coupled steam turbines and/or generators with outputs greater than 50 MW (see ISO 10816-2);f) synchronizing clutches which couple the gas turbine to a steam turbine or generator (see ISO 10816-2);g) coupled compressors (see ISO 10816-3);h) gearbox vibration (see this clause);i) rolling element bearing vibration.This part of ISO 10816 is applicable to other driven equipment not included in this list of exclusions.This part of ISO 10816 is applicable to machines which can be coupled to a gearbox, but does not addressthe evaluation of the vibration condition of those gears. Specialist techniques are required for evaluating thevibration condition of gears which are outside the scope of this part of ISO 10816.The numerical values specified are not intended to serve as the only basis for judging the severity of vibration.For gas turbine sets, it is also common to judge the vibration based on measurements taken on the rotatingshafts. For such vibration measurement requirements, see ISO 7919-1 and ISO 7919-4.