BS EN ISO 14126-1999 纤维增强塑料复合材料.平面方向压缩性的测定

百检网 2021-07-16
标准号:BS EN ISO 14126-1999
中文标准名称:纤维增强塑料复合材料.平面方向压缩性的测定
英文标准名称:Fibre-reinforced plastic composites. Determination of compressive properties in the in-plane direction
标准类型:Q23
发布日期:1999/11/15 12:00:00
实施日期:1999/11/15 12:00:00
中国标准分类号:Q23
国际标准分类号:83.120
适用范围:1 This International Standard specifies two methods for determining compressive properties, in directions paradel to the plane of lamination, of fibre-reinforced plastic composites. 2 The compressive properties are of interest for specifications and quality-control purposes. 3 Two loading methods and two types of specimen are described. They are: — Method 1: provides shear loading of the specimen (gauge length unsupported). — Method 2: provides end loading, or mixed loading, of the specimen (gauge length unsupported). NOTE For tabbed specimens end-loaded using method 2, some load is transferred into the specimen gauge length by shear through the tabs. — Type A specimen: rectangular cross-section, fixed thickness, end-tabbed. — Type B specimen: rectangular cross-section, range of thicknesses, untabbed or end-tabbed (two sizes available). Any combination of test method and specimen may be used, provided that the requirements of subclause 9.8 are satisfied and that the specimen is representative of the material under test. These alternative test conditions will not necessarily give the same result. The type A specimen is the preferred specimen for unidirectionally reinforced materials tested in the fibre direction. For other materials, the type A or B specimen may be used. The type B2 specimen is preferred for mat, fabric and other multidirectionally reinforced materials. 4 The methods are suitable for fibre-reinforced thermoplastic and thermosetting plastic composites. Unreinforced and particle-filled plastics, as well as those reinforced with short fibres (less than 1 mm in length), are covered by ISO 604 (see bibliography). 5 The methods are performed using specimens which may be machined from a test panel made in accordance with ISO 1268 or equivalent methods, or from finished or semi-finished products. 6 The methods specify required dimensions for the specimen. Tests which are carried out on specimens of other dimensions, or on specimens which are prepared under different conditions, may produce results which are not comparable. Other factors, such as the speed of testing, the support fixture used and the condition of the specimens, can influence the results. Consequently, when comparative data are required, these factors must be carefully controlled and recorded. 7 Fibre-reinforced plastics are usually anisotropic. It is therefore often useful to cut test specimens in at least the two main directions of anisotropy, or in directions previously specified (for example a lengthwise direction associated with the production process).

百检能给您带来哪些改变?

1、检测行业全覆盖,满足不同的检测;

2、实验室全覆盖,就近分配本地化检测;

3、工程师一对一服务,让检测更精准;

4、免费初检,初检不收取检测费用;

5、自助下单 快递免费上门取样;

6、周期短,费用低,服务周到;

7、拥有CMA、CNAS、CAL等权威资质;

8、检测报告权威有效、中国通用;

客户案例展示

  • 上海朗波王服饰有限公司
  • 浙江圣达生物药业股份有限公司
  • 天津市长庆电子科技有限公司
  • 上海纽特丝纺织品有限公司
  • 无锡露米娅纺织有限公司
  • 东方电气风电(凉山)有限公司