BS EN 13598-2-2009 无压力地下排水和排污用塑料管道系统.未增塑聚氯乙烯(PVC-U),聚丙烯(PP)和聚乙烯(PE).第2部分:交通范围和地下设施中检修孔和检查室用规范

标准号：BS EN 13598-2-2009
中文标准名称：无压力地下排水和排污用塑料管道系统.未增塑聚氯乙烯(PVC-U),聚丙烯(PP)和聚乙烯(PE).第2部分:交通范围和地下设施中检修孔和检查室用规范
英文标准名称：Plastics piping systems for nonpressure underground drainage and sewerage — Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 2: Specifications for manholes and inspection chambers in traffic areas and dee
标准类型：Q81
发布日期：2009/2/28 12:00:00
实施日期：2009/2/28 12:00:00
中国标准分类号：Q81
国际标准分类号：93.030
引用标准：EN 124-1994;EN 476-1997;EN 681-1-2002;EN 681-2-2000;EN 728-1997;EN 681-3-2002;EN 681-4-2000;EN 744-1995;EN 922-1994;EN 1277-2003;EN 1401-1;EN 1852-1;EN 12061;EN 12666-1;EN 13101-2002;EN 13476-1;EN 13476-2;EN 13476-3;EN 14396-2004;CEN/TS 14541;EN 14758-1;E
适用范围：This European Standard specifies the definitions and requirements for buried manholes andinspection chambers installed to a maximum depth of 6 m from ground level to the invert of the mainchamber and manufactured from unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP),polypropylene with mineral modifier (PP-MD) or polyethylene (PE). These products are intended foruse in pedestrian or vehicular traffic areas and underground installations conforming to the generalrequirements given in EN 476 and are used outside the building structure (application area code “U”).They are therefore marked accordingly with a “U”. Such products are also deemed to meet therequirements of EN 13598-1 for application area U without the need for further testing. If additionallymarked application area D then these products must additionally be tested to show compliance to theelevated temperature cycling requirement of Clause 10 of EN 13598-1.This European Standard is only applicable to those chamber / manhole items where the manufacturerhas clearly stated in the documentation how the components shall be assembled to create a completemanhole or inspection chamber.The inspection chambers covered by this European Standard comprise the following: inspection chambers providing access to the drainage or sewerage system by means ofinspection and cleaning equipment. chambers, designated as manholes providing man access to the drainage or sewerage system.The inspection chamber / manhole can be manufactured by various methods e.g. injection moulding,rotational moulding, low-pressure moulding or fabricated from components made in accordance withother standards.The jointing of components can be achieved using: elastomeric ring seal joints; adhesive joints for PVC-U; welded joints for PVC-U, PP and PE; extrusion welding; mechanical jointing.NOTE Both manholes and inspection chambers can be site assembled from different components, but canalso be manufactured as a single unit. In either case, the following functional parts can be recognized:a) base (always present)In case of a one-piece chamber or manhole, the base part ends at a distance of 300 mmmeasured from the top of the main channel;b) riser (depth dependent);c) telescopic part (design dependent);d) cone (dependent on the design of near surface components and their recommended installation);e) other near surface components