IEC 60987-2007 核电站.对安全性很重要的仪器仪表和控制.基于计算机系统的硬件设计要求

百检网 2021-07-15
标准号:IEC 60987-2007
中文标准名称:核电站.对安全性很重要的仪器仪表和控制.基于计算机系统的硬件设计要求
英文标准名称:Nuclear power plants - Instrumentation and control important to safety - Hardware design requirements for computer-based systems
标准类型:F69;F07
发布日期:2007/8/1 12:00:00
实施日期:1999/12/31 12:00:00
中国标准分类号:F69;F07
国际标准分类号:27.120.20;35.240.99
引用标准:IEC 60780;IEC 60812;IEC 60880;IEC 61000;IEC 61025;IEC 61513-2001;IEC 62138;ISO 9001;IAEA NS-G 1.3;IAEA 50-C/SG-Q-1996
适用范围:1.1 GeneralThis International Standard is applicable to NPP computer-system hardware for systems ofClass 1 and 2 (as defined by IEC 61513).The structure of this standard has not changed significantly from the original 1989 issue;however, some issues are now covered by standards which have been issued in the interim(for example, IEC 61513 for system architecture design) and references to new standardshave been provided where applicable. The text of the standard has also been modified toreflect developments in computer system hardware design, the use of pre-developed (forexample, COTS) hardware and changes in terminology.Computer hardware facilities used for software loading and checking are not considered toform an intrinsic part of a system important to safety and, as such, are outside the scope of this standard.NOTE 1 Class 3 computer-system hardware is not addressed by this standard, and it is recommended that such systems should be developed to commercial grade standards.NOTE 2 In 2006 the development of a new standard to address hardware requirements for “very complex” hardware was discussed within IEC SC 4**. If such a standard is developed then that standard would be used for the development of “very complex” hardware in preference to IEC 60987.1.2 Use of this standard for pre-developed (for example, COTS) hardware assessmentAlthough the primary aim of this standard is to address aspects of new hardwaredevelopment, the processes defined within this standard may also be used to guide theassessment and use of pre-developed hardware, such as COTS hardware. Guidance hasbeen provided in the text concerning the interpretation of the requirements of this standard when used for the assessment of such components. In particular, the quality assurance requirements of 4.3, concerning configuration control, apply.Pre-developed components may contain firmware (as defined in 3.8), and, where firmwaresoftware is deeply imbedded, and effectively “transparent” to the user, then IEC 60987 should be used to guide the assessment process for such components. An example of where this approach is considered appropriate is in the assessment of modern processors which contain a microcode. Such a code is generally an integral part of the “hardware”, and it is therefore appropriate for the processor (including the microcode) to be assessed as an integrated hardware component using this standard.Software which is not firmware, as described above, should be developed or assessedaccording to the requirements of the relevant software standard (for example, IEC 60880 for Class 1 systems and IEC 62138 for Class 2 systems).1.3 Applicability of this standard to programmable logic devices developmentI&C components may include programmable logic devices that are given their specificapplication logic design by the designer of the I&C component, as opposed to the chipmanufacturer. Examples of such devices include complex programmable logic devices (CPLD)and field programmable gate arrays (FPGA).While the programmable nature of these devices gives the development processes used forthese devices, some of the characteristics of a software development process and the design processes used for such devices, are very similar to those used to design logic circuits implemented with discrete gates and integrated circuit packages. Therefore, the design processes and design verification applied to programmable logic devices should comply with the relevant requirements of this standard (i.e. taking into account the particular features of the design processes of such devices). To the extent that software-based tools are used to support the design processes for programmable logic devices, those software tools should generally follow the guidance provided for software-based development tools in the appropriate software standard, i.e. IEC 60880 (Class 1 systems) or IEC 62138 (Class 2 systems).

百检能给您带来哪些改变?

1、检测行业全覆盖,满足不同的检测;

2、实验室全覆盖,就近分配本地化检测;

3、工程师一对一服务,让检测更精准;

4、免费初检,初检不收取检测费用;

5、自助下单 快递免费上门取样;

6、周期短,费用低,服务周到;

7、拥有CMA、CNAS、CAL等权威资质;

8、检测报告权威有效、中国通用;

客户案例展示

  • 上海朗波王服饰有限公司
  • 浙江圣达生物药业股份有限公司
  • 天津市长庆电子科技有限公司
  • 上海纽特丝纺织品有限公司
  • 无锡露米娅纺织有限公司
  • 东方电气风电(凉山)有限公司