ISO 3951-5-2006 计量检验的抽样程序.第5部分:按接收质量限(AQL)检索的计量检验连续抽样计划的规范(已知标准偏差)

百检网 2021-08-02
标准号:ISO 3951-5-2006
中文标准名称:计量检验的抽样程序.第5部分:按接收质量限(AQL)检索的计量检验连续抽样计划的规范(已知标准偏差)
英文标准名称:Sampling procedures for inspection by variables - Part 5: Sequential sampling plans indexed by acceptance quality limit (AQL) for inspection by variables (known standard deviation)
标准类型:A00
发布日期:1999/12/31 12:00:00
实施日期:1999/12/31 12:00:00
中国标准分类号:A00
国际标准分类号:03.120.30
引用标准:ISO 2859-1-1999;ISO 3534-1;ISO 3534-2;ISO 3951-1-2005
适用范围:This part of ISO 3951 specifies a system of sequential sampling plans (schemes) for lot-by-lot inspection by variables. The schemes are indexed in terms of a preferred series of acceptance quality limit (AQL) values, ranging from 0,01 to 10, which are defined in terms of percent nonconforming items.The schemes of ISO 3951 are intended to induce a supplier through the economic and psychological pressure of lot non-acceptance to maintain a process average at least as good as the specified AQL value, while at the same time providing an upper limit for the risk to the consumer of accepting the occasional poor lot.The schemes are designed to be applied to a continuing series of lots, that is, a series long enough to allow the switching rules (Clause 6) to be applied. These switching rules provide:— automatic protection to the consumer (by means of a switch to tightened inspection or discontinuation of sampling inspection) should a deterioration in quality be detected;— an incentive (at the discretion of the responsible authority) to reduce inspection costs (by means of a switch to reduced inspection) should consistently good quality be achieved.This part of ISO 3951 is designed for use under the following conditions:a) where the inspection procedure is to be applied to a continuing series of lots of discrete products all supplied by one producer using one production process. If there are different producers or production processes, apply this part of ISO 3951 to each one separately;b) where only a single quality characteristic, x, of these products is taken into consideration, which must be measurable on a continuous scale;c) where the uncertainty of the measurement system is negligible with respect to the production process standard deviation;d) where production is stable (under statistical control) and the quality characteristic, x, is distributed according to a normal distribution (or a close approximation to the normal distribution) or a distribution which may be mathematically transformed to a normal distribution;e) where the standard deviation of the quality characteristic, x, is known;CAUTION — The procedures in this part of ISO 3951 are not suitable for application to lots that have been screened previously for nonconforming items.f) where a contract or standard defines an upper specification limit, U, a lower specification limit, L, or both; an item is qualified as conforming if and only if its measured quality characteristic, x, satisfies the appropriate one of the following inequalities:

百检能给您带来哪些改变?

1、检测行业全覆盖,满足不同的检测;

2、实验室全覆盖,就近分配本地化检测;

3、工程师一对一服务,让检测更精准;

4、免费初检,初检不收取检测费用;

5、自助下单 快递免费上门取样;

6、周期短,费用低,服务周到;

7、拥有CMA、CNAS、CAL等权威资质;

8、检测报告权威有效、中国通用;

客户案例展示

  • 上海朗波王服饰有限公司
  • 浙江圣达生物药业股份有限公司
  • 天津市长庆电子科技有限公司
  • 上海纽特丝纺织品有限公司
  • 无锡露米娅纺织有限公司
  • 东方电气风电(凉山)有限公司